SS 304 Sheets & Plates
AISI 304 (UNS S30400) · DIN 1.4301 · JIS SUS304 · IS X04Cr19Ni9
SS 304 Sheets & Plates in ready stock at our Madurai godowns, solution annealed, 0.5–50 mm thick · 2B / BA / No.4 / HR. Band-saw cut to your sizes with mill test certificates on request.
I. Sizes & weights
Nominal weights at 8 g/cm³ · 0.5–50 mm thick · 2B / BA / No.4 / HR| Thickness mm | kg / m² | kg / sheet 1250 × 2500 | |
|---|---|---|---|
| 0.8 | 6.40 | 20.0 | |
| 1 | 8.00 | 25.0 | |
| 1.6 | 12.8 | 40.0 | |
| 2 | 16.0 | 50.0 | |
| 3 | 24.0 | 75.0 | |
| 5 | 40.0 | 125.0 | |
| 6 | 48.0 | 150.0 | |
| 8 | 64.0 | 200.0 | |
| 10 | 80.0 | 250.0 | |
| 12 | 96.0 | 300.0 | |
| 16 | 128.0 | 400.0 | |
| 20 | 160.0 | 500.0 | |
| 25 | 200.0 | 625.0 | |
| 32 | 256.0 | 800.0 | |
| 40 | 320.0 | 1,000.0 | |
| 50 | 400.0 | 1,250.0 |
II. Chemical composition (% by weight)
| Element | C | Mn | Si | Cr | Ni | S |
|---|---|---|---|---|---|---|
| Min | – | – | – | 18.0 | 8.0 | – |
| Max | 0.08 | 2.00 | 0.75 | 20.0 | 10.5 | 0.030 |
Typical standard ranges. Every mill lot ships with its own test certificate on request.
III. Mechanical properties
- Tensile
- 515 MPa min
- Yield
- 205 MPa min
- Hardness
- 201 HB max
- Elongation
- 40% min
IV. Supply condition
- Condition
- Solution annealed
- Machinability
- Fair
- Forms
- plate
- Cutting
- Band saw ±1 mm
- SKU
- SST-SS-03
V. Weigh it, then request it.
Locked to SS 304SS 304 · 8 g/cm³
W = T × W × L × ρ ÷ 1,000,000 · ρ = 8 g/cm³ · rounded to 0.1 kg. Theoretical weight; actual mill weight can vary by ±2–3%.
Tanks, hoppers, kitchen equipment
About SS 304
Can you cut SS 304 to my sizes?
Yes. SS 304 is band-saw cut to ±1 mm. Send piece sizes and quantities with your request; cutting is quoted with the material.
Is a mill test certificate provided with SS 304?
An MTC is supplied with mill material on request, traceable to the heat number.
What sizes are in stock?
0.5–50 mm thick · 2B / BA / No.4 / HR. For large tonnage, message us to reserve material.
What are the equivalents of SS 304?
AISI 304 (UNS S30400), DIN 1.4301, JIS SUS304, IS X04Cr19Ni9. Equivalents are close matches; confirm against your drawing's specification.
